hi..
i did configure ipv6 for two NIC cards, first i have eth1 to configure ipv6, i did configure and it works but suddenly someone that NIC card. so i have to re-conf it (eth2) but those both card gave different result:
eth0 Link encap:Ethernet HWaddr 00:26:18:EE:C6:4F
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:28 Base address:0xe000
eth1 Link encap:Ethernet HWaddr 00:24:01:D2:2B:D1
inet addr:202.47.88.XX Bcast:202.47.88.79 Mask:255.255.255.240
inet6 addr: fe80::224:1ff:fed2:2bd1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:311913 errors:0 dropped:0 overruns:0 frame:0
TX packets:105610 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:102114023 (97.3 MiB) TX bytes:13764699 (13.1 MiB)
Interrupt:20 Base address:0x8c00
he-ipv6 Link encap:IPv6-in-IPv4
inet6 addr: 2001:470:35:XXX::2/64 Scope:Global
inet6 addr: fe80::ca2f:584c/128 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:1410 dropped:0 overruns:0 carrier:1410
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1593 errors:0 dropped:0 overruns:0 frame:0
TX packets:1593 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:224484 (219.2 KiB) TX bytes:224484 (219.2 KiB)
sit0 Link encap:IPv6-in-IPv4
inet6 addr: ::202.47.88.XX/96 Scope:Compat
inet6 addr: ::127.0.0.1/96 Scope:Unknown
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
sit1 Link encap:IPv6-in-IPv4
inet6 addr: fe80::ca2f:5843/64 Scope:Link
inet6 addr: 2001:470:35:XXX::2/64 Scope:Global
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:92 errors:0 dropped:0 overruns:0 frame:0
TX packets:172 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:17746 (17.3 KiB) TX bytes:125612 (122.6 KiB)
while for eth2 it doesnt have sit0 and sit1, why? what is sit1 and sit0 exactly?
eth0 Link encap:Ethernet HWaddr 00:26:18:EE:C6:4F
inet addr:202.47.88.67 Bcast:202.47.88.79 Mask:255.255.255.240
inet6 addr: fe80::226:18ff:feee:c64f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:628364 errors:0 dropped:0 overruns:0 frame:0
TX packets:10502 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:67415880 (64.2 MiB) TX bytes:2127919 (2.0 MiB)
Interrupt:28 Base address:0xa000
eth2 Link encap:Ethernet HWaddr 00:40:F4:EA:7D:DD
inet addr:172.27.11.66 Bcast:172.27.11.255 Mask:255.255.255.0
inet6 addr: fe80::240:f4ff:feea:7ddd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:327438 errors:336305 dropped:292246 overruns:336305 frame:0
TX packets:838 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:31261577 (29.8 MiB) TX bytes:86715 (84.6 KiB)
Interrupt:20 Base address:0x4c00
he-ipv6 Link encap:IPv6-in-IPv4
inet6 addr: fe80::ca2f:5843/128 Scope:Link
inet6 addr: 2001:470:35:270::2/64 Scope:Global
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:459 errors:0 dropped:0 overruns:0 frame:0
TX packets:589 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:394222 (384.9 KiB) TX bytes:90240 (88.1 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:145 errors:0 dropped:0 overruns:0 frame:0
TX packets:145 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14879 (14.5 KiB) TX bytes:14879 (14.5 KiB)
