horsemen
Newbie
Posts: 18
|
 |
« on: December 21, 2010, 10:30:42 am » |
|
Good day, I have set obtained a /48 and succseffly set up the tunnel, my router can ping6 ipv6.google.com and I get a responce, I can also visit it on my browser. however my other host on my lan can ping only the directly connected interface and nothing else. Any help would be aprechiated. Below is the router set up
ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:29:FB:C0:CF
inet addr:75.152.109.214 Bcast:75.152.111.255 Mask:255.255.240.0
inet6 addr: 2001:470:b115::2/48 Scope:Global
inet6 addr: fe80::20c:29ff:fefb:c0cf/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:158668 errors:0 dropped:0 overruns:0 frame:0
TX packets:165704 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:33953895 (32.3 MiB) TX bytes:22004342 (20.9 MiB)
Interrupt:67 Base address:0x2000
eth1 Link encap:Ethernet HWaddr 00:0C:29:FB:C0:D9
inet6 addr: 2001:470:b115::3/48 Scope:Global
inet6 addr: fe80::20c:29ff:fefb:c0d9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:162193 errors:0 dropped:0 overruns:0 frame:0
TX packets:163066 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:18880419 (18.0 MiB) TX bytes:18916588 (18.0 MiB)
Interrupt:67 Base address:0x2080
he-ipv6 Link encap:IPv6-in-IPv4
inet6 addr: 2001:470:b115::1/48 Scope:Global
inet6 addr: fe80::4b98:6dd6/128 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:74935 errors:0 dropped:0 overruns:0 frame:0
TX packets:74970 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7818272 (7.4 MiB) TX bytes:9295572 (8.8 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2379 errors:0 dropped:0 overruns:0 frame:0
TX packets:2379 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3452546 (3.2 MiB) TX bytes:3452546 (3.2 MiB)
ip -6 route show
unreachable ::/96 dev lo metric 1024 expires 21334176sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable ::ffff:0.0.0.0/96 dev lo metric 1024 expires 21334176sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
2001:470:b115::/48 via :: dev he-ipv6 metric 256 expires 21334280sec mtu 1480 advmss 1420 hoplimit 4294967295
2001:470:b115::/48 dev eth0 metric 256 expires 21334280sec mtu 1500 advmss 1440 hoplimit 4294967295
2001:470:b115::/48 dev eth1 metric 256 expires 21334280sec mtu 1500 advmss 1440 hoplimit 4294967295
unreachable 2002:a00::/24 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:7f00::/24 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:a9fe::/32 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:ac10::/28 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:c0a8::/32 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:e000::/19 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 3ffe:ffff::/32 dev lo metric 1024 expires 21334177sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
fe80::/64 dev eth0 metric 256 expires 21334118sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 dev eth1 metric 256 expires 21334126sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 via :: dev he-ipv6 metric 256 expires 21334280sec mtu 1480 advmss 1420 hoplimit 4294967295
default dev he-ipv6 metric 1024 expires 21334280sec mtu 1480 advmss 1420 hoplimit 4294967295
Config Script I use
modprobe ipv6
ip tunnel add he-ipv6 mode sit remote 216.66.38.58 local 75.152.109.214 ttl 255
ip link set he-ipv6 up
ip addr add 2001:470:b115::1/48 dev he-ipv6
ip route add ::/0 dev he-ipv6
ip addr add 2001:470:b115::2/48 dev eth0
ip addr add 2001:470:b115::3/48 dev eth1
ip -f inet6 addr
sysctl -w net.ipv6.conf.all.forwarding=1
And my LAN host
ifconfig
eth0 Link encap:Ethernet HWaddr 00:26:18:3b:0b:1f
inet addr:10.0.0.10 Bcast:10.255.255.255 Mask:255.0.0.0
inet6 addr: fe80::226:18ff:fe3b:b1f/64 Scope:Link
inet6 addr: 2001:470:b115::4/48 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:164831 errors:0 dropped:0 overruns:0 frame:0
TX packets:161984 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:19638355 (18.7 MiB) TX bytes:18800088 (17.9 MiB)
Interrupt:222 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:23 errors:0 dropped:0 overruns:0 frame:0
TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2840 (2.7 KiB) TX bytes:2840 (2.7 KiB)
ip -6 route show
2001:470:b115::/48 dev eth0 proto kernel metric 256 expires 2590586sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 dev eth0 metric 256 mtu 1500 advmss 1440 hoplimit 4294967295
default via fe80::20c:29ff:fefb:c0d9 dev eth0 proto kernel metric 1024 expires 224sec mtu 1500 advmss 1440 hoplimit 64
Again Thanks for any help
Shawn Foisy
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #1 on: December 21, 2010, 10:34:08 am » |
|
First, a couple things.
The IP on he-ipv6 should be 2001:470:b115::2 and your default route should point to 2001:470:b115::1
The IP you have on eth0 should be out of the /48 you grabbed.
EDIT:
Same thing for eth1..take a /64 out of your /48 and assign an address out of that
Same thing for your lan host...take another /64 out of your /48 and assign an IP address out of that
|
|
|
|
« Last Edit: December 21, 2010, 10:35:53 am by cholzhauer »
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #2 on: December 21, 2010, 10:40:50 am » |
|
Routed /48: 2001:470:b115::/48
the 2001:470:b115:: is my routable address space so using 2001:470:b115::X should be alright?
I am going to make the change noted above and let you know.
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #3 on: December 21, 2010, 10:46:49 am » |
|
If that's what you say it is, so be it.
The problem is you're using that same network for your tunnel /64
Let me see if I can make this clearer... Lets say 2001:db8:1:1::/64 is your tunnel /64 and 2001:db8:f::/48 is your routed /48. The address on he-ipv6 should be 2001:db8:1:1::2 and the default route should point to 2001:db8:1:1::1 For eth0 on your tunnel machine, you would select a /64 out of your /48, say 2001:db8:f:1::/64 and assign an address, say 2001:db8:f:1::1. Then, for eth1, you assign another, say 2001:db8:f:2::1 (assuming those are connected to different networks). For eth0 on your host computer, you select another, say 2001:db8:f:3::1
Make sense?
What is your tunnel /64 that's listed on the webpage?
|
|
|
|
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #4 on: December 21, 2010, 11:00:28 am » |
|
Routed /64: 2001:470:1d:417::/64
so I made some changes to the script
modprobe ipv6
ip tunnel add he-ipv6 mode sit remote 216.66.38.58 local 75.152.109.214 ttl 255
ip link set he-ipv6 up
ip addr add 2001:470:1d:417::2/64 dev he-ipv6
ip route add ::/0 dev he-ipv6
ip addr add 2001:470:b115::1:1/64 dev eth0
ip addr add 2001:470:b115::2:1/64 dev eth1
ip -f inet6 addr
sysctl -w net.ipv6.conf.all.forwarding=1
I think this right?
so on the host machine I would use say 2001:470:b115::3:1/64 dev eth0 ? and what about the next machine on the LAN i could use 2001:470:b115::3:2/64 ?
but eth1 and LAN machine are connected via a swith so they should be on the same network 2001:470:b115::2:2/64 ?
I am going to restart the router with the canges and see if anything works.
also how do i make the default route: 2001:db8:1:1::1 For eth0 on my tunnel machine?
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #5 on: December 21, 2010, 11:06:29 am » |
|
You are hosting this tunnel on a PC, right? (as opposed to a cisco router or something) If eth1 and your lan machines are on the same network segment, then yes, they should have the same /64. One host could be 2001:470:b115::2:2, one could be 2001:470:b115::2:3, ect. If you did that, 2001:470:b115::3:1 would be acceptable to use on eth0 I'm not sure what you mean by this also how do i make the default route: 2001:db8:1:1::1 For eth0 on my tunnel machine?
|
|
|
|
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #6 on: December 21, 2010, 11:30:31 am » |
|
You are hosting this tunnel on a PC, right? (as opposed to a cisco router or something)
yes its a CentOS Linux box or well VM
and I ment how do I add the default route
ip -6 route add :: via 2001:470:1d:417::1/64 ?
So I canged the address and they are
eth0 Link encap:Ethernet HWaddr 00:0C:29:FB:C0:CF
inet addr:75.152.109.214 Bcast:75.152.111.255 Mask:255.255.240.0
inet6 addr: 2001:470:b115::1:1/64 Scope:Global
inet6 addr: fe80::20c:29ff:fefb:c0cf/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2539 errors:0 dropped:0 overruns:0 frame:0
TX packets:2274 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2522712 (2.4 MiB) TX bytes:378260 (369.3 KiB)
Interrupt:75 Base address:0x2000
eth1 Link encap:Ethernet HWaddr 00:0C:29:FB:C0:D9
inet6 addr: 2001:470:b115::2:1/64 Scope:Global
inet6 addr: fe80::20c:29ff:fefb:c0d9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:412 errors:0 dropped:0 overruns:0 frame:0
TX packets:422 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:48828 (47.6 KiB) TX bytes:51682 (50.4 KiB)
Interrupt:75 Base address:0x2080
he-ipv6 Link encap:IPv6-in-IPv4
inet6 addr: 2001:470:1d:417::2/64 Scope:Global
inet6 addr: fe80::4b98:6dd6/128 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:841 errors:0 dropped:0 overruns:0 frame:0
TX packets:850 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:622887 (608.2 KiB) TX bytes:231573 (226.1 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2636 errors:0 dropped:0 overruns:0 frame:0
TX packets:2636 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3861316 (3.6 MiB) TX bytes:3861316 (3.6 MiB)
and LAN host is now 2001:470:b115::2:2/64 and it can ping 2001:470:b115::2:1 not a problem but not 2001:470:b115::1:1 I get destination unreachable address unreachable. If I try to ping the tunnel 2001:470:1d:417::2 I get Connect: Network unreachable.
Sorry for my ignorance, and thaks for the help
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #7 on: December 21, 2010, 11:42:26 am » |
|
So if you do a "ping6 2001:470:1d:417::1" it doesn't work? That's the other end of the tunnel, which means your runnel isn't up. But, from the traffic statistics, it looks like traffic is being sent. (There's more traffic there than there is on eth1) You're going to want to route your /48 out eth1. As for your default route, take a look at this (Which, if you don't have a default route, pings wouldn't be working) http://www.cyberciti.biz/tips/linux-ipv6-default-route-not-working.html |
|
|
|
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #8 on: December 21, 2010, 11:52:38 am » |
|
this is what I get from the router
[root@d75-152-109-214 ~]# ping6 2001:470:1d:417::1
PING 2001:470:1d:417::1(2001:470:1d:417::1) 56 data bytes
From 2001:470:1d:417::2 icmp_seq=0 Time exceeded: Hop limit
From 2001:470:1d:417::2 icmp_seq=1 Time exceeded: Hop limit
[root@d75-152-109-214 ~]# ping6 ipv6.google.com
PING ipv6.google.com(iw-in-x68.1e100.net) 56 data bytes
64 bytes from iw-in-x68.1e100.net: icmp_seq=0 ttl=54 time=101 ms
64 bytes from iw-in-x68.1e100.net: icmp_seq=1 ttl=54 time=101 ms
64 bytes from iw-in-x68.1e100.net: icmp_seq=2 ttl=54 time=102 ms
as for routing the /48
[root@d75-152-109-214 ~]# ip -6 route add 2001:470:b115::/48 via 2001:470:b115::2:1 dev eth1
RTNETLINK answers: No route to host
I'm lost
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #9 on: December 21, 2010, 11:53:58 am » |
|
What do your routing tables look like now
|
|
|
|
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #10 on: December 21, 2010, 11:56:03 am » |
|
[root@d75-152-109-214 ~]# ip -6 route show
:: via 2001:470:1d:417::1 dev he-ipv6 metric 1024 expires 21333788sec mtu 1480 advmss 1420 hoplimit 4294967295
unreachable ::/96 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable ::ffff:0.0.0.0/96 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
2001:470:1d:417::/64 via :: dev he-ipv6 metric 256 expires 21333739sec mtu 1480 advmss 1420 hoplimit 4294967295
2001:470:b115::/64 dev eth0 metric 256 expires 21333739sec mtu 1500 advmss 1440 hoplimit 4294967295
2001:470:b115::/64 dev eth1 metric 256 expires 21333739sec mtu 1500 advmss 1440 hoplimit 4294967295
unreachable 2002:a00::/24 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:7f00::/24 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:a9fe::/32 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:ac10::/28 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:c0a8::/32 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:e000::/19 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 3ffe:ffff::/32 dev lo metric 1024 expires 21333664sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
fe80::/64 dev eth0 metric 256 expires 21333618sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 dev eth1 metric 256 expires 21333622sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 via :: dev he-ipv6 metric 256 expires 21333739sec mtu 1480 advmss 1420 hoplimit 4294967295
default dev he-ipv6 metric 1024 expires 21333739sec mtu 1480 advmss 1420 hoplimit 4294967295
[root@d75-152-109-214 ~]#
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #11 on: December 21, 2010, 12:03:29 pm » |
|
default dev he-ipv6 metric 1024 expires 21333739sec mtu 1480 advmss 1420 hoplimit 4294967295
That's your default route. I've read that for some kernels, you need to add that route from the link before ip route add 2000::/3 dev he-ipv6 |
|
|
|
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #12 on: December 21, 2010, 12:18:34 pm » |
|
i've added the route.
here is what I get from router
[root@d75-152-109-214 ~]# ping6 ipv6.google.com
PING ipv6.google.com(iw-in-x63.1e100.net) 56 data bytes
64 bytes from iw-in-x63.1e100.net: icmp_seq=0 ttl=54 time=101 ms
64 bytes from iw-in-x63.1e100.net: icmp_seq=1 ttl=54 time=102 ms
64 bytes from iw-in-x63.1e100.net: icmp_seq=2 ttl=54 time=101 ms
--- ipv6.google.com ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 9875ms
rtt min/avg/max/mdev = 101.408/101.679/102.186/0.443 ms, pipe 2
[root@d75-152-109-214 ~]# ping6 2001:470:1d:417::1
PING 2001:470:1d:417::1(2001:470:1d:417::1) 56 data bytes
From 2001:470:1d:417::2 icmp_seq=0 Time exceeded: Hop limit
From 2001:470:1d:417::2 icmp_seq=1 Time exceeded: Hop limit
From 2001:470:1d:417::2 icmp_seq=2 Time exceeded: Hop limit
--- 2001:470:1d:417::1 ping statistics ---
5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 5380ms
also i did
ip route add 2001:470:b115::/48 dev eth1
[root@d75-152-109-214 ~]# ip -6 route show
:: via 2001:470:1d:417::1 dev he-ipv6 metric 1024 expires 21333005sec mtu 1480 advmss 1420 hoplimit 4294967295
unreachable ::/96 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable ::ffff:0.0.0.0/96 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
2001:470:1d:417::/64 via :: dev he-ipv6 metric 256 expires 21332957sec mtu 1480 advmss 1420 hoplimit 4294967295
2001:470:b115::/64 dev eth0 metric 256 expires 21332957sec mtu 1500 advmss 1440 hoplimit 4294967295
2001:470:b115::/64 dev eth1 metric 256 expires 21332957sec mtu 1500 advmss 1440 hoplimit 4294967295
2001:470:b115::/48 dev eth1 metric 1024 expires 21334321sec mtu 1500 advmss 1440 hoplimit 4294967295
unreachable 2002:a00::/24 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:7f00::/24 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:a9fe::/32 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:ac10::/28 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:c0a8::/32 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 2002:e000::/19 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
unreachable 3ffe:ffff::/32 dev lo metric 1024 expires 21332882sec error -101 mtu 16436 advmss 16376 hoplimit 4294967295
2000::/3 dev he-ipv6 metric 1024 expires 21334136sec mtu 1480 advmss 1420 hoplimit 4294967295
fe80::/64 dev eth0 metric 256 expires 21332836sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 dev eth1 metric 256 expires 21332840sec mtu 1500 advmss 1440 hoplimit 4294967295
fe80::/64 via :: dev he-ipv6 metric 256 expires 21332957sec mtu 1480 advmss 1420 hoplimit 4294967295
default dev he-ipv6 metric 1024 expires 21332957sec mtu 1480 advmss 1420 hoplimit 4294967295
[root@d75-152-109-214 ~]#
Host still can't ping outside 2001:470:b115::2:/64
Thanks for your help so far
|
|
|
|
|
Logged
|
|
|
|
|
cholzhauer
|
|
« Reply #13 on: December 21, 2010, 12:30:11 pm » |
|
Something strange is happening [carl@mars ~]$ ping6 2001:470:1d:417::2
PING6(56=40+8+8 bytes) 2001:470:c27d:e000:20c:29ff:fe8a:1618 --> 2001:470:1d:417::2
16 bytes from 2001:470:1d:417::2, icmp_seq=0 hlim=57 time=252.102 ms
16 bytes from 2001:470:1d:417::2, icmp_seq=1 hlim=57 time=149.014 ms
16 bytes from 2001:470:1d:417::2, icmp_seq=2 hlim=57 time=144.916 ms
16 bytes from 2001:470:1d:417::2, icmp_seq=3 hlim=57 time=144.671 ms
^C
--- 2001:470:1d:417::2 ping6 statistics ---
4 packets transmitted, 4 packets received, 0.0% packet loss
round-trip min/avg/max/std-dev = 144.671/172.676/252.102/45.889 ms
[carl@mars ~]$ ping6 2001:470:1d:417::1
PING6(56=40+8+8 bytes) 2001:470:c27d:e000:20c:29ff:fe8a:1618 --> 2001:470:1d:417::1
^C
--- 2001:470:1d:417::1 ping6 statistics ---
3 packets transmitted, 0 packets received, 100.0% packet loss
According to that, I can ping your side of the tunnel, but not HE's side I can even ping your eth1
[carl@mars ~]$ ping6 2001:470:b115::2:1
PING6(56=40+8+8 bytes) 2001:470:c27d:e000:20c:29ff:fe8a:1618 --> 2001:470:b115::2:1
16 bytes from 2001:470:b115::2:1, icmp_seq=0 hlim=57 time=146.072 ms
16 bytes from 2001:470:b115::2:1, icmp_seq=1 hlim=57 time=145.695 ms
16 bytes from 2001:470:b115::2:1, icmp_seq=2 hlim=57 time=145.200 ms
^C
--- 2001:470:b115::2:1 ping6 statistics ---
3 packets transmitted, 3 packets received, 0.0% packet loss
round-trip min/avg/max/std-dev = 145.200/145.656/146.072/0.357 ms
|
|
|
|
|
Logged
|
|
|
|
horsemen
Newbie
Posts: 18
|
|
« Reply #14 on: December 21, 2010, 12:37:45 pm » |
|
can you ping6 2001:470:b115::2:2 ?
and that is weird?
I will restart the router maybe somthing got cofufled in changing settings?
|
|
|
|
|
Logged
|
|
|
|
|
